DIY CNC Stand Off Blocks

DIY CNC Machine with Blocks and red dust boot.

 

Here are four DIY CNC Stand Off blocks which were printed on our shop  with a 0.02 setting and Medium (25%) fill in white ABS plastic. The idea is to provide a stand off of the material to allow a 2D cut through to fall though to the table below instead of potentially getting wound up in the cutter or using tabs.  This also protects the bed from the cutter too and the material is held in place with step clamps (there will be another post on this).  You can get an STL copy of the blocks at Tinkercad by clicking here and downloading the STL file.  Worth note is we would suggest printing these one at time rather than 4 at a time as the plastic will stay warmer as doing 4 at a times means the head with do a layer on each [block] and while it does that, the bond will be lessened and while these will not need to hold a lot of force (as they have a good sized surface area), you still want them to be semi-strong.

XYZprinting Da Vinci 2.0 Duo 3D Printer, Grey

by XYZprinting [XYZprinting,Inc]
Rank/Rating: 294139/-
Price: -

CNC Support Blocks

DIY3DTech-CNC Support Block for holding stock

 

In this project we will build a simple 1.5″(h) x 1.5″(w) x1.5″(d) block with a 0.5″(h) x 1.0″(w) x 1.0″(d) notch.  The idea is we print four (4) of these blocks, one for each corner of our material (a sheet good) and each corner is placed in the notch and the material is then clamped down for machining.

The idea is the material will be held about 1.0″ above the bed of the machine allowing the tool cut though without damaging the bed. The sheet good material should be of a size which allows it enough stiffness to avoid a sag, however if this is not the case.  A simple 1.0″ square cube could also be printed and slipped under the material for additional support.  However use care as the tool might strike this piece damaging it or sending it flying so always ensure safety first when working with power tools.

This file can be found on TinkerCad site under the name DIY3DTech – CNC Support Block and by clicking the prior link.  We also post more pictures of this in use soon.

XYZprinting Da Vinci 2.0 Duo 3D Printer, Grey

by XYZprinting [XYZprinting,Inc]
Rank/Rating: 294139/-
Price: -

 

3D Printed CNC Router Base – Part 2

3D printed CNC router base with laser mount and dust collection

Well the part is now printed, however not with out some headaches as it took a couple trys to get the final product out the door.  The base setting was printed .04, with 25% (medium) infill and normal shell thickness at fast speed got the job done.  In addition, we had to use a “raft” to get the large surface area to stick to the bed of the Da Vinci 2.0 Duo 3D printer as in the prior prints it kept lifting off the bed and damaging the print.

Part of this issue is likely the bed temperature being a little low as ours is set 95 deg-C and would prefer it to be at 100 or 110 deg-C to make it a little more sticky if you will and this is where the “raft” came in as with its liter weight, its sticks better and then the base has a better surface to stick to.  However in the end a portion of the print did lift up however it was late in the print cycle so it was printing the tube portion and had little affect.  As it is likely that the temperature at the edges of the bed are too cool to effectively hold a large surface area print.

Notice there are a few striations due to the rough print setting and since the part will be sanded and printed, this should not be an issue. In addition, this part was finished with our heat gun process which we will cover in a future post and likely a video too.

XYZprinting Da Vinci 2.0 Duo 3D Printer, Grey

by XYZprinting [XYZprinting,Inc]
Rank/Rating: 294139/-
Price: -

3D Printed CNC Router Base – Part 1

3d Printed CNC Router for Laser & Vacuum attachment

This week we are working on building a combination, laser & vacuum base for other shop 3d CNC router.  The file can be found on ThinkerCad by clicking this link. and please follow along as I will be posting more photos and videos of build and operation.  As the idea here is to build a base which adds a vacuum port as well as a laser alignment holder next to cutting motor.  While the original base was built as a 2D sketch in iDraw on the Mac (there is also an iDraw iPad version too), and then exported as an SVG (vector file) which was than imported into  Tinkercad and built up into a STL file which was then exported into the XYZ Printing slicing App for printing on the Da Vinci 2.0 Duo 3D printer.  The resulting part was then printed in ABS at .04 with 25% fill and normal shells.  One of the changes which had to be made was the use of a “raft” because large surface of the print.  See more on this in the next part of the installment project.

XYZprinting Da Vinci 2.0 Duo 3D Printer, Grey

by XYZprinting [XYZprinting,Inc]
Rank/Rating: 294139/-
Price: -